Installing A Bathtub
Installing A Bathtub
Blog Article
This great article below in relation to Installing A Bathtub is exceptionally engaging. Try it and draw your own personal findings.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the task can move easily; if you have to open up a wall to eliminate the old bathtub as well as position the new bath tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified yourself for the job as well as fit trying it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This short article will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a new tub and do not require to transform the arrangement of your previous water supply pipes.
Your devices and also product list need to consist of the following:
Getting ready for the Setup
To start with, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system as well as check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait up until the tub has been made use of at the very least when as this will resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with wetness and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I am just very taken with A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed the post. I beg you take the opportunity to share this page if you enjoyed reading it. We thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule Your Service
Report this page